Channel Master 6136 (This is a receiver only and will have a separate dish positioner) BUTTONS ON THE RECEIVER
BUTTONS ON THE REMOTE
INDICATORS ON THE RECEIVER
HOW TO PROGRAM A SATELLITE These type of receivers do not go by satellite names, the customer should have a list of numbers that correspond to the satellites. (EX: Satellite 01 will be F1, 02 is F4, etc.). 1. Find a satellite number that the customer does not use. 2. Start on a satellite next to or near the satellite that is being programmed. 3. Go to a channel that is active on both the satellite you are starting from and the satellite to be programmed. 4. Press selecT; display reads [‘SEL]. 5. Press zero (0) twice; display reads [00] then [ID]. 6. Press the ID code which is factory preset at 1, 2, 3; display reads [C##]. If 1, 2, 3 does not work then go to "How to Change the ID Code if it is Forgotten". 7. Follow the correct procedure: [A] If you are starting from a satellite with the opposite polarity, tap the UP (east) or DOWN (west) button just until the picture is gone. -Next, press the H/V button on the receiver one time to reverse the polarity; display reads [‘H EN] for normal polarity or [‘H OD] for reversed polarity. -If there is a picture at this time and it is the correct satellite, then proceed to step 8; otherwise continue moving up or down. [B] If you are starting from a satellite with the same polarity, then tap the UP (east) or DOWN (west) button until a different picture comes in. If the picture is correct, then proceed to step 8; otherwise continue moving. 8. To store the satellite: Press select, display reads [‘SEL]; press 1, 2; display reads [‘PP], then press the number of the satellite you are storing (from 1-33). Press select again; display reads [‘PP##] then [‘C##]. 9. To exit the programming mode: Press select, display reads [‘SEL]; then zero (0) twice; display reads [‘C##]. 10. This completes the programming process.
1. Press select; display reads [‘SEL]. 2. Press 0 twice; display reads [00] then [ID]. 3. Press 1, 2, 3; display reads [C##]. 4. Press select; display reads [‘SEL]. 5. Press 1, 3; display reads [‘PE]. 6. Press the number of the satellite to be erased; display reads [‘P##]. 7. Press select and the satellite should be erased now; display reads [‘SEL]. 8. Press select, then 0 twice to exit the programming mode; display reads [C##].
1. Press select; display reads [‘SEL]. 2. Press 0 twice; display reads [00] then [ID]. 3. Press 1, 2, 3; display reads [C##]. 4. Press select; display reads [‘SEL]. 5. Press 1, 8; display reads [‘ID]. 6. Press any three digit number you want to be the code; display reads [‘C##]. 7. Press select, then 0 twice to exit the programming mode; display reads [C##].
1. Press select; display reads [‘SEL]. 2. Press 6 1; display reads [61 momentarily]. 3. Press 8 5 2; display reads [C##]. 4. The ID code is now set to 1, 2, 3 as it was originally.
1. Go to the channel that is to be locked or unlocked. 2. Press select; display reads [‘SEL]. 3. Press 0 twice; display reads [00] then [ID]. 4. Press 1, 2, 3; display reads [C##]. 5. Press select; display reads [‘SEL]. 6. Press 1, 2, 3, 4, 5, 6; display reads [‘CL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘CL], then [OFF], then [‘C##] if the lock was turned off. 7. Press select; display reads [‘SEL]. 8. Press 0 twice; display reads [CL].
1. Go to the satellite that is to be locked on or lock removed. 2. Press select; display reads [‘SEL]. 3. Press 0 twice; display reads [00] then [ID]. 4. Press 1, 2, 3; display reads [C##]. 5. Press select; display reads [‘SEL]. 6. Press 1, 4; display reads [‘PL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘PL], then [OFF], then [‘C##] if the lock was turned off. 7. Press select; display reads [‘SEL]. 8. Press 0 twice; display reads [‘C##].
1. Go to the satellite and channel that is to be locked on or lock removed. 2. Press select; display reads [‘SEL]. 3. Press 0 twice; display reads [00] then [ID]. 4. Press 1, 2, 3; display reads [C##]. 5. Press select; display reads [‘SEL]. 6. Press 1, 5; display reads [‘SL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘SL], then [OFF], then [‘C##] if the lock was turned off. 7. Press select; display reads [‘SEL]. 8. Press 0 twice; display reads [‘C##]. |
|
|
We have designed this site with both our current and prospective customers in mind. If you have any bugs, broken links to report, comments, questions or suggestions about Orbit or this web site, please feel free to send a message to webmaster.