Chaparral Monterey 35,55 and 95
The Chaparral Monterrey features up to 100 favorite satellite TV or radio
stations, 31-day/9-event timer, auto tune, multi-receiver capability, picture in
picture, Dolby Surround Sound, MTS Stereo output, UHF remote and on-screen/front
panel displays. The Monterrey is the state-of-the-art receiver that includes
multiple audio/video inputs and outputs as well as coaxial inputs for dual
C-Band or C/Ku-Band reception.
LEGEND
Blue = Buttons on Remote
MASTER PASSWORD
2 – 3 – 4
- 5
COMMON PROBLEMS
- If the screen says "SOURCE NOT MONTERREY", then press UP
ARROW LARGE SELECT.
- If you are not getting audio on GE3-16 (CNNi/CNNfn), press SETUP
1, 2, 1.
RE-PROGRAM A SATELLITE:
1. Go to the satellite that is to be reprogrammed.
2. Select a channel that will be active on the satellite to be programmed.
3. Press the MENU button. Press 7 for Sat/Ch
Setup (even if it does not display a line number 7). It may ask for a password.
If so, press 2-3-4-5.
It should now be in the Sat/Ch Setup menu. See below:
7. SAT/CHAN SETUP
ð DISH POSITION: 1111
POLARITY: 168
FREQUENCY: 3.7400 GHZ
VIDEO LEVEL: NORMAL
BANDWIDTH: 26 MHz
TI FILTERS: NONE
VIDEO INVERSION: OFF
RESTORE CHANNEL: 05 |
4. The arrow should be pointing at dish position, if not, press UP
ARROW or DOWN ARROW so that it is. Press the
ENTER button. The screen should now be in the Set
Satellite Position menu.
5. Press LEFT ARROW (east) or RIGHT
ARROW (west) to tune to the satellite to be programmed. Stop when you
come across any picture or black screen. Check the picture to see if it is the
correct satellite. If so, proceed with step 6. If not, continue moving.
Possible problem: It is picking up the satellites with the
opposite format. (EX: You are looking for a Galaxy format sat. and they are
picking up a Telstar format sat. If this is happening, then try the instructions
below:
a. Try to locate a satellite that is next to the one to be programmed. Then
move in the correct direction towards the satellite to be programmed, just
until the picture is gone and stop.
b. Press MENU twice to save the satellite in that
position. It will return to the previous menu. Make a note of the polarity
number and the channel number. ( TIP: The polarity range is 80-220. The normal
settings are 101 for horizontal and 178 for vertical ).
c. Press VIEW and go up or down one channel
(even-to-odd or odd-to-even).
d. Press MENU and then 7
(password 2-3-4-5
if necessary). Make a note of the polarity and channel number. Move the arrow
down to polarity if necessary. Then, enter the polarity that you had on the
previous channel by direct entry or with the left/right arrows.
e. Press VIEW and go back to the previous channel
and repeat this step entering the opposite polarity from the other channel.
(Steps 4 and 5 is to reverse the format.
f. Press VIEW and verify if a picture is in. If
not then, press MENU - 7 again
and move the arrow to polarity and use LEFT ARROW or
RIGHT ARROW to adjust for a picture or press autotune.
g. If no picture will come in, then start over or call 1-888-FIX-MY-TV
(349-6988).
6. Press MENU twice to save the satellite in
that position. It will return to the previous menu. Press VIEW
and verify that it is stored. If not repeat from step 1.
PROGRAM A NEW SATELLITE (ADDING IT TO THE RECEIVER'S
DATABASE)
1. Go to a satellite with the same format and is near to the satellite
that is to be programmed.
2. Select a channel that is active on the satellite you are starting from and on
the satellite to be programmed.
3. Press MENU then 9 for
Sat. Definition. It may ask for a password. If so, press 2
– 3 – 4 - 5.
It should now be in the Sat Definition menu. See below:
9. Sat. Definition
ð ADD NEW SATELLITE
FORMAT: 4 GHZ
SAT TYPE: GALAXY
INSERT SYNC: AUTO
ERASE SATELLITE: G1
RESTORE SAT: G1 |
4. Move the arrow to Add New Satellite if necessary.
5. Press ENTER. At the bottom of the screen it will
display "Enter New Satellite: __"
6. Press the letter and number of the new satellite name.
7. It may display "Press Enter To Activate". If so, press ENTER.
8. It will display "Satellite S1 Added" (or whatever
name you gave it ). (The new satellite now is stored on the satellite
position that you are starting from.
9. Press VIEW several times to exit the menus.
Press VIEW again to see what satellite it displays.
If it is the correct satellite name that you just entered then proceed with step
10; if not, repeat the steps again.
10. Press the MENU button. Press 7
for Sat/Ch Setup (even if it does not display a line number 7). It may
ask for a password. If so, press 2 – 3
– 4 - 5. It
should now be in the Sat/Ch Setup menu. See Below:
7. SAT/CHAN SETUP
ð DISH POSITION: 1111
POLARITY: 168
FREQUENCY: 3.7400 GHZ
VIDEO LEVEL: NORMAL
BANDWIDTH: 26 MHz
TI FILTERS: NONE
VIDEO INVERSION: OFF
RESTORE CHANNEL: 05 |
11. Press UP ARROW or DOWN
ARROW so that the arrow is pointing at dish position. Press the ENTER
button. The screen should now be in the Set Satellite Position menu.
12. Press LEFT ARROW (east) or RIGHT
ARROW (west) to tune to the satellite to be programmed. Stop when you
come across any picture or black screen. Check the picture to see if it is
correct satellite. If so, proceed with step 13. If not, continue moving.
13. Press MENU twice to
save the satellite in that position. It will return to the previous menu. Press VIEW
and verify that it is stored. If not repeat from step 1.
ADDING A NEW FAVORITE CHANNEL
- Press MENU followed by FAVORITE.
- With the cursor on the NUMBER field, press the LEFT
ARROW or RIGHT ARROW to display the
number of the favorite channel you wish to use.
- Press DOWN ARROW to move the cursor to the
GROUP field and press RIGHT ARROW to select
which favorite group you would like to add this channel to. Up to 16 groups
are available. If you wish to change the name of the group then you can
press ENTER while point to GROUP and it will
bring up the NAME MENU.
- Press DOWN ARROW to move the cursor to the
SATELLITE field and use LEFT ARROW or RIGHT
ARROW to select the satellite of the favorite channel.
- Press DOWN ARROW to move the cursor to the
CHANNEL field and select the channel number of the favorite channel.
- Press DOWN ARROW to move the cursor to the
AUDIO field. If the favorite is a TV channel then select 0. If it is a
satellite radio station then select the appropriate audio channel.
- Press DOWN ARROW to move the cursor to the
NAME field and press enter to display the NAME
MENU to select the name for the favorite channel.
NAME MENU
This menu allows you to specify the name you which to use for any favorite
channel or group (up to 12 characters including spaces). The name menu is also
used to name the external input sources and the satellite types. To use the
naming menu:
- Use the UP ARROW, DOWN
ARROW, LEFT ARROW, and RIGHT
ARROW keys to point the cursor at each character and press ENTER
to select that character.
- To erase a character, press CANCEL. You may
also exit this menu without the name by pressing CANCEL
until the previous menu is displayed.
- When you are finished changing the name press MENU twice.
|