Chaparral Sierra-3, Cheyenne Models
The Chaparral Sierra 3 and Cheyenne feature auto tuning, up to 100 favorite channel programming, Infrared Remote, on-screen menus, coaxial inputs for dual C-Band or C/Ku-Band reception, audio/video inputs and outputs. LEGEND Blue = Buttons on Remote MASTER PASSWORD 2 – 3 – 4 - 5 1. If the satellite to be programmed is already stored in the wrong position, then it must be erased before it can be programmed. Click here to go to the Erase a Satellite section. 2. Start on a satellite next to or near the satellite that is being programmed. 3. Press the TUNING MODE button to bring up the dish tuning on the screen. The word DISH POSITION and SIGNAL STRENGTH will be displayed at the bottom of the screen. If dish, polarity, audio and video tuning modes do not come up, see the Unlocking the Tuning Mode section. After turning off the tuning mode lock and polarity, audio and video modes appear, but the dish position still will not come up. Turn off the dish mode lock. See the Unlocking Dish Mode section. 4. Press SAT button then the satellite name your looking for. (EX: SAT S 4). The receiver will change channels from what it was on. Go to an active channel on both the satellite you are starting from and the satellite you are programming with the channel up or down button or enter it directly. If you are starting from a satellite with the same format you should still have a picture on the satellite that you are on, if the satellite has an opposite format there will not be a picture. It will also have the name of the satellite that you are programming on the screen. 5. Tap the UP ARROW (west) or DOWN ARROW to move the dish toward the satellite you are looking for. Stop when you see either a picture or a clear black screen and check to see what satellite you are on. If the picture is the correct satellite, then proceed to step 6. If it is the wrong satellite, then continue to move. If it is moving the wrong direction, go the other way until desired picture is found. 6. If all the above steps worked correctly, you should be on the correct channel you were looking for and it should display the name of the satellite to be stored at the top of the screen. If not, then press SAT and the name of the satellite again. 7. Press STORE with a pointed instrument. The STORE button is a recessed button. If it displays "Storing Is Locked" then go to Unlocking the Store Lock section. After pressing store, you can press AUTOTUNE to tune even more, press STORE again if you want to save the changes, otherwise press CANCEL. Press the TUNING MODE until VOLUME MODE is displayed so that it is in normal viewing mode. Then hit VIEW to verify that it is stored. -If the incorrect name is on the screen, then proceed from step 6 again. 8. If all steps worked correctly then you are finished. 9. If you cannot get the satellite programmed then try the Alternate Method below.
1. Press A followed by the F to enter the Advanced Functions menu. 2. Press 5 - 4 for Erase A Satellite. If it displays to enter a password, then press 2 – 3 – 4 - 5; otherwise, proceed to step 3. 3. Press SAT to select the satellite to be erased. 4. Press ENTER to erase the satellite. 5. Press VIEW to exit the function.
1. Press A followed by F buttons to enter the Advanced Functions menu. 2. Press 3 - 2 for Tuning Mode Lock. If it displays to enter a password, then press 2 – 3 – 4 - 5; otherwise, proceed to step 3. 3. Press UP ARROW or DOWN ARROW to select the "Tuning Is Unlocked" option. 4. Press ENTER. 5. Press VIEW if necessary.
UNLOCKING THE DISH TUNING MODE 1. Press A followed by the F to enter the Advanced Functions menu. 2. Press 3 - 4 for Tuning Mode Lock. If it displays to enter a password, then press 2 – 3 – 4 - 5; otherwise, proceed to step 3. 3. Press UP ARROW or DOWN ARROW to select the "Dish Is Unlocked" option. 4. Press ENTER. 5. Press VIEW if necessary.
1. Press A followed by F buttons to enter the Advanced Functions menu. 2. Press 3 - 3 for Store Lock. If it displays to enter a password, then press 2 – 3 – 4 - 5; otherwise, proceed to step 3. 3. Press UP ARROW or DOWN ARROW to select the "Store Is Unlocked" option. 4. Press ENTER. 5. Press VIEW if necessary. |
|
|
We have designed this site with both our current and prospective customers in mind. If you have any bugs, broken links to report, comments, questions or suggestions about Orbit or this web site, please feel free to send a message to webmaster.