(This receiver does not have any
buttons on the front of the receiver)
This receiver features on-screen displays, IR remote, audio/video
outputs, C/Ku compatible (external switch required) and LNBF compatible.
LEGEND
Blue = Buttons on Remote or Receiver
HOW TO PROGRAM A SATELLITE
1. Go to a satellite that is near to the satellite to be programmed
that has the same polarity. **You may use a satellite with the
opposite polarity but programming will be a little more difficult.**
2. Select a channel that is active on the satellite to be programmed
and on the satellite that you are starting from. Verify this throughout
the procedure to prevent confusion.
3. Go into program mode: Move the switch located on the back of the
receiver to the right for Program mode, it is on the top-right side.
*Caution-There is another switch beside this button that controls the LNB
selection. Be sure not to move this switch.
4. The screen will display Program Mode on the top of the screen.
5. Press SAT and a menu will be displayed.
(See figure 1.) This menu will not stay on the screen very long, so it
needs to be read quickly. Make a note of the Setup No., Sat Name,
Position, Polarity, Skew, and Channel. This will help in programming the
new satellite and in case any errors are made you will have the
information to restore it.
___________________________
* PROGRAM MODE *
Right Arrow
SETUP NO |
05 |
Each time SAT is
pressed the arrow will move down to the next selection. |
SAT NAME: |
G4 |
|
POSITION: |
---- |
To change a selection, press SAT
until the |
BAND: |
C |
arrow is beside it and then use STEP |
POLARITY: |
NORMAL |
UP/DOWN
to change them. |
SKEW: |
VER 180 |
|
CHANNEL: |
06 |
|
6. Press SAT until the arrow is pointing at
Position. If you are starting from a satellite with the same format, then
tap EAST or WEST
until another picture is received. If not, then reverse the Polarity using
the STEP UP/DOWN arrows and then move.
7. After finding the correct satellite, press SAT
until the arrow is pointing at Setup No.
8. While watching the Position number, press STEP
UP to begin scrolling through the Setup Numbers until you
find one that does not have a number beside the Position, instead it will
have blank squares like in the figure 1. *Note: The Setup Nos. that have a
blank position will also have G1 in the Sat Name.* If you cannot find a
blank Position for a Setup No., then find a Setup No. that has a satellite
name that is not used or is an old satellite.
9. Make a note of the Setup No., because this is the one you will use
to store the new satellite under. *Note: The menu will blank off the
screen if nothing is pressed within a few seconds. If this happens you may
have to scroll to the Setup No again.
10. You are now going to change the Sat Name to the correct satellite.
Press SAT button until the arrow is pointing
at Sat Name and then press the letter and number
of the satellite to be programmed. You may use STEP
UP/DOWN and EAST/WEST to change the letter and number.
11. You are now going to change the Band, Polarity, Skew, and Channel
to the same settings as they were when you began. Verify that you are on
the same channel as before. Press SAT until
the arrow is pointing at Polarity, Skew, Band (if necessary), Channel (if
necessary), then use STEP UP/DOWN arrows to
change the setting until correct settings are displayed. (These are the
settings you wrote down in step 5 for the satellite that you are starting
on.) If it is necessary to change the Skew number, use the EAST/WEST
to do this.
If you are starting on a satellite with the opposite polarity then
make sure that the Polarity is reversed. When you reverse the Polarity
the Skew should change also, if not then use STEP
UP/DOWN and EAST/WEST to reverse the
Skew.
12. If all the settings are correct then you are ready to store them.
To store the information the menu must be on the screen when the store
button is pressed. Locate STORE above the
number 1 key. Press SAT and quickly verify
that the Setup number is correct and the Sat Name is correct. If all is OK
then press STORE while the writing is on the
screen. The screen should display "Stored" when the button is
pressed.
13. Move the switch on the back of the receiver to the RUN
mode.
HOW TO ERASE A SATELLITE
1. Go to the satellite to be erased.
2. Go into program mode: Move the switch located on the back of the
receiver to the right for Program mode, it is on the top-right side.
*Caution-There is another switch beside this button that controls the LNB
selection. Be sure not to move this switch.
3. Locate ERASE above the 2
key on the remote. Press SAT and while the
menu is on the screen press ERASE.
4. The only item that will change on the screen is the dish position
will be blank. This means that it is erased.
5. Move the switch on the back of the receiver to Run Mode.
PARENTAL LOCKS
There are no parental locks in this receiver. But, you can cause a
channel to be skipped when pressing STEP UP/DOWN.
1. Go to the channel to be skipped (or to restore a skipped channel).
2. To skip the channel press STORE, to
restore the channel press ERASE.
3. The channel can still be accessed and viewed by entering the channel
number.
HOW TO CHANGE SATELLITES
1. Press SAT then press letter
then number of the satellite.
Or
2. Press SAT twice, then use STEP
UP/DOWN to scroll through the programmed
satellites. Stop when the desired satellite is displayed, then press SAT
again within 5 seconds.
HOW TO CHANGE THE AUDIO MODE
1. Press CH until the cursor is pointing
at Audio Mode.
2. Use STEP UP/DOWN to change to the
desired mode.
3. To change the frequency, press CH until
the cursor is pointing at Audio Freq., then use STEP
UP/DOWN to set the desired frequency or enter the three-digit
frequency.
4. Press STORE to save the audio
changes or VIEW just to exit the menu with no
save.
|